本田奥德赛电动尾门安装说明

电动尾门套装

专业安装工具，扳手等

Installation notes1. Before installing the tailgate, check the status of the trunk door.2. Before installation, check whether the vehicle is scratched, take photos and inform the owner.3, after installing the product, you need to learn the electric tail gate to work properly.4. The pictures in this description are for reference only. Please take the material object as the criterion and install the same method.5. For easy installation, please read the installation instructions carefully before installation. Please protect the vehicles and not scrape them when installing.6. Please check regularly whether there are any loose parts in connection with the vehicle so as to ensure the safety of use.

Electric tail gate height setting methodPush the electric tail door to the target height, press the switch button installed at the tail door for 3-5 seconds to emit a long sound of 'prompt', release the button and then press the button again, the tail door closed in place to emit a 'prompt tone' two tones, indicating that the height of the electric tail door is set to complete

Control box wiring instructionsA. power cordB. tail door key and three way wireC. control box

1. the electric lever on the left, the electric lever on the right2., the power button on theright3., the button on the4. door and the three way wire.5. the position of the red arrow, the 2 plugs, the 6. control box

Accessories listm

Installation steps*1. mounting bracket and electric pole1. according to the above picture operation: use the prying plate to remove the clasp from the decorative board.

2. remove the right upper bracket of the original vehicle and replace it with a new right upper bracket. Screw with original screw.3. Remove the right lower bracket and replace it with a new right lower bracket (ball head facing the outside of the car) fixed with special screws

4. remove the left upper bracket of the original vehicle, replace it with the new upper bracket, or use the original screw and the gasket to fix it.5. Remove the left lower bracket and replace it with a new left lower bracket (ball head facing the outside of the car) and fix it with a new screw.

6. bracket and electric pole installation effect picture.

*2. how to thread the electric pole wire?1. Punch holes in the right upper bracket position, arrange lines, and clamp the original vehicle waterproof rubber plug (the same way on both sides)2. wire arrangement of electric poles to tail door cover plate position

*3. car main driving position before installation switch.1. find the power below the main driving position.2. remove the original car fuse and plug in the power plug of the electric tail door.

3. remove the trim panel on the side of the main driver, locate the ground screw on the picture, and connect the ground wire of the electric tail gate.4. main driver remove the decorative panel, remove the original car idle button, install the electric tail door switch button.

5. remove the decoration and find the white plug of the original car.6. electric front door switch ILL line receives gray line on white plug, from left to right second holes.

*4. central control line connection1. remove the plastic cover on the left rear seat and locate the central control line.2. the Yellow middle control line of the electric tail door is connected with the yellow line on this socket.

3. place the driver's power cord and front switch line as shown in the picture to the rear of the car.4. main drive power cord and front switch line and central control line are arranged according to yellow arrow to tail door.

5. wire the electric tail gate together according to the location of the picture and the line of the original car.

*5. install electric suction lock.1. dismantle the original vehicle screw and remove the lock. Install new upper suction lock with screws and gaskets as shown in the picture.2. picture on the location of the arrow on the three line plug and upper suction lock docking

3. dismantle the original car lock, place the hole at the bottom of the original car lock and add a shim and restore it.

6. front switch and three way wire connection.1. locate the socket on the rear door.2. pull down the plug of the original car and plug in the plug of the electric tail box door.

1. locate the socket on the rear door.2. pull down the plug of the original car and plug in the plug of the electric tail box door.

*7. installation control box1. color matching, pay attention to check whether it is inserted in place.2. the same color corresponds to white, white to white, purple to purple.

3. tear off the adhesive tape on the back.4. install the control box in the yellow circle position shown in the picture.

*8. install the electric tail door button on the tail box door.1. dismantle the tail door switch of the original car decoration, install the electric tail door control switch.2. tail door button plug and three way plug connection.

*9. check after installation.1. is the plug in place?2. is the screw in place?3. wire damage, may be caught.4. is the power on suction lock working properly?5. is the function of the remote controller and the driving button switch normal?

*10. electric tail gate learning settingsAfter the installation of the electric tailgate, the learning settings must be made before use. First push the electric tail door manually to the usual height, press the electric tail door switch button above the tail door for 3-5 seconds, release the hand after hearing a long sound of 'drop', then press the electric tail door switch button again, the electric tail door begins to close down, the tail door will be closed in place after the 'drop' two sounds. The electric tail gate is completed. If there is no 'drop' sound, it is necessary to relearn the above method according to the above method. (another thing is that the door can not be locked by the electric tail door, which requires manual assistance to close the rear door at this time)

*11. if electric tail door can not open normallyFind the emergency safety lock of the original car in the trunk. Open the emergency cover and pull the emergency switch.

*12. causes of problems & results1. wrong installation: tail door closed.2. the bracket screws are not replaced as required: the tail door will not close, and the electric pole will be damaged.3. control box plug is not inserted in place: Electric tail door will be unbalanced.4. electric pole ball and clip spring are not stuck in place: the electric pole will fall off during use.5 other plugs are not inserted in place or fall off: failure of function6. Installation position of the upper suction lock deviates from the center: the tail door does not close, the gap is big, and the tension is tight, which causes the switch to sound loudly.7. the new vehicle has not started for a long time. The power consumption is small: the switch door is abnormal and needs to restart the vehicle.8. above the tail door, add the sound insulation cotton 5KG above effect: need control box afterburner.9. vehicles need to relearn after power failure.

*13. failure phenomenon & troubleshooting method1. the original vehicle remote control can not control the operation of the tail box door.1. check whether the yellow central control line is connected well.2. after the installation of the electric tailgate, it is necessary to use the electric tail door button installed on the tail box door for the first time to learn.2. electric tail door is not working after installation.1. check whether the power cord is connected well, 12v-16v.2. check whether the fuse is inserted.3. check whether the ground wire is connected well.3. the electric tailgate door is not in place.1. is the left and right bracket of electric poles wrong?2. control box plug is inserted.3. do the bracket screws meet the requirements?4. original car tail door cover about two black glue loose?The operation of the electric tailgate switch is abnormal.1. is there any wrong installation of the left and right bracket of the electric pole?2. control box socket is inserted.3. do the bracket screws meet the requirements?

*14. use of electric tail door1. install the electric tail door switch button in the driving position: click the on / off electric tail door.2. remote control: press the tail door button of the remote control for 3 seconds to turn on / off the electric tailgate.

3. tail door fitted with electric tail door button: press the button to close the electric tail door.4. original car tail box button: Click to open the electric tail door.

*15 . use of electric tail door1. Anti-clip function: when the obstacle is just below, the electric tail door will stop running or rebound and reset at a uniform speed when it encounters the obstacle in the process of closing.2. Open door anti-collision function: when the obstacle is in the rear of the electric tail door, when the electric tail door opens, the obstacle will stop and rebound at a uniform speed.Be careful! The pressure on the left and right sides of the tailgate door is heavier. Please do not try. If you want to see all the consequences, please take care of yourself.

DisclaimerThe problems and losses caused by improper installation and use are not within the scope of our company's warranty. Please read the instructions carefully before use. The picture is for reference only.